FriendlyELEC NanoPi M2 - Samsung Quad Core A9, 1Gb, Gbit Lan,

FriendlyELEC NanoPi M2 - Samsung Quad Core A9, 1Gb, Gbit Lan,

Artikelnummer: 7-134577
GTIN: 4038816096692
Hersteller:

28,69 €

inkl. 19% USt. , zzgl. (Standard)

ab	Stückpreis / Stk
3	28,12 €*
5	27,83 €*
10	27,26 €*

Momentan nicht verfügbar

Beschreibung
Benachrichtigen, wenn wieder verfügbar

Introduction

Overview

Front

Back

frameless

The NanoPi M2 is another Samsung 4418 based ARM board released by FriendlyARM after the NanoPi 2 and NanoPi 2 Fire. It is only two thirds the size of the Raspberry Pi. It is open source. It works with Ubuntu Core, Ubuntu Mate, Debian, Android 5.1 and etc.
Compared to the Raspberry Pi 2 the NanoPi M2 uses the Samsung Cortex-A9 S5P4418 Soc. It integrates Gbps Ethernet, AXP228 PMU which supports software power-on/off and wake up functions. It can be powered via the MicroUSB port
In such a small board it still integrates rich interfaces and ports. Besides the popular HDMI, 3.5mm audio jack, onboard microphone, four USB hosts and Gbit Ethernet it has a Raspberry Pi compatible 40 pin GPIO pin header and various video interfaces such as a DVP camera interface, an LCD interface which supports I2C capacitive LCD and etc. In addition, for user’s convenience it has a serial debug port for debugging and development.

Hardware Spec

CPU: S5P4418, 400Mhz~1.4GHz
DDR3 RAM: 32bit 1GB DDR3
MicroSD Slot x1
Connectivity: Gbps Ethernet port(RTL8211E)
Audio: 3.5mm audio jack/Via HDMI
Microphone: 1 x onboard Microphone
USB Host: 4 x USB 2.0 Host, two are standard type A ports and the other two are 2.54mm pitch pin headers
Micro USB: 1 x USB 2.0 Client
LCD Interface: 0.5 mm pitch SMT FPC seat, for full-color LCD (RGB: 8-8-8)
HDMI: HDMI 1.4A, Type-A, 1080P60
DVP Camera Interface: 0.5mm pitch FPC socket. It includes ITU-R BT 601/656 8-bit, I2C and IO
GPIO1: 2.54mm pitch 40pin, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, PWM, IO etc
Debug Serial Port: 4Pin 2.54mm pitch pin header
User Key: 1 x Power , 1 x Reset
LED: 1 x Power LED, 1 x System LED
RTC: RTC Pins
Power: DC 5V/2A
PCB Dimension(mm): 64 x 56, Six Layer
Temperature measuring range: -10? to 80?
OS/Software: u-boot, Android5.1/4.4, Debian Jessie 8

Diagram, Layout and Dimension

Layout

NanoPi M2 Interfaces and Ports

NanoPi M201 Interfaces and Ports

GPIO1 Pin Spec

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	VDD_5V
3	I2C0_SDA	4	VDD_5V
5	I2C0_SCL	6	DGND
7	GPIOD8/PPM	8	UART3_TXD/GPIOD21
9	DGND	10	UART3_RXD/GPIOD17
11	UART4_TX/GPIOB29	12	GPIOD1/PWM0
13	GPIOB30	14	DGND
15	GPIOB31	16	GPIOC14/PWM2
17	SYS_3.3V	18	GPIOB27
19	SPI0_MOSI/GPIOC31	20	DGND
21	SPI0_MISO/GPIOD0	22	UART4_RX/GPIOB28
23	SPI0_CLK/GPIOC29	24	SPI0_CS/GPIOC30
25	DGND	26	GPIOB26
27	I2C1_SDA	28	I2C1_SCL
29	GPIOC8	30	DGND
31	GPIOC7	32	GPIOC28
33	GPIOC13/PWM1	34	DGND
35	SPI2_MISO/GPIOC11	36	SPI2_CS/GPIOC10
37	AliveGPIO3	38	SPI2_MOSI/GPIOC12
39	DGND	40	SPI2_CLK/GPIOC9

This GPIO pin spec is a little bit different from that of the NanoPi 2. Here is a comparison table of the two:40 pins GPIO comparison table

Debug Port(UART0)

Pin#	Name
1	DGND
2	VDD_5V
3	UART_TXD0
4	UART_RXD0

DVP Camera IF Pin Spec

Pin#	Name
1, 2	SYS_3.3V
7,9,13,15,24	DGND
3	I2C0_SCL
4	I2C0_SDA
5	GPIOB14
6	GPIOB16
8,10	NC
11	VSYNC
12	HREF
14	PCLK
16-23	Data bit7-0

RGB LCD IF Pin Spec

Pin#	Name	Description
1, 2	VDD_5V	5V Output, it can be used to power LCD modules
11,20,29, 37,38,39,40, 45	DGND	Gound
3-10	Blue LSB to MSB	RGB blue
12-19	Green LSB to MSB	RGB green
21-28	Red LSB to MSB	RGB red
30	GPIOB25	available for users
31	GPIOC15	occupied by FriendlyARM one wire technology to recognize LCD models and control backlight and implement resistive touch, not applicable for users
32	XnRSTOUT Form CPU	low when system is reset
33	VDEN	signal the external LCD that data is valid on the data bus
34	VSYNC	vertical synchronization
35	HSYNC	horizontal synchronization
36	LCDCLK	LCD clock, Pixel frequency
41	I2C2_SCL	I2C2 clock signal, for capacitive touch data transmission
42	I2C2_SDA	I2C2 data signal, for capacitive touch data transmission
43	GPIOC16	interrupt pin for capacitive touch, used with I2C2
44	NC	not connected

Note

SYS_3.3V: 3.3V power output
VVDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
All pins are 3.3V, output current is 5mA
GPIO1's pin spec is a little bit different from that of the NanoPi 2. Refer to this comparison table 40 pins GPIO comparison table
For more details refer to the document: NanoPi-M2-1602-Schematic.pdf

Board Dimension

For more details refer to the document: NanoPi-M2-1602-Dimensions(dxf).zip

Artikelgewicht:

0,03 kg
kwh/1000h:

.00
Lumen:

.00
Watt:

.00
Nennlebensdauer in Std.:

.00
Schaltzyklen:

.00
Opt. Umgebungstemperatur in °C:

.00

Kontaktdaten

E-Mail

Ich willige ein, dass meine Angaben (Anrede, Name, Vorname, Firma, E-Mail-Adresse, Telefon) sowie meine Nachricht ausschließlich zum Zwecke der Bearbeitung und Abwicklung meiner Anfrage verarbeitet werden. ()